GEBE Academy

Τα μαθήματα κατάρτισης είναι τόσο διαφορετικά όσο και οι απαιτήσεις σας, από ολοκληρωμένες τεχνικές συνεδρίες για τη διαχείριση προϊόντων και κατηγοριών έως συνεδρίες σε αίθουσα διδασκαλίας για τις ομάδες πωλήσεων:

  • Λειτουργία & εφαρμογή
  • Τεχνικό υπόβαθρο & πολυπλοκότητα
  • Επιχειρηματολογία αξίας & επισημάνσεις προϊόντος

Παρακαλούμε επικοινωνήστε με τον αντιπρόσωπο του λογαριασμού σας για την ατομική σας συνεδρία.

Ως μέσο για να καταστήσουμε τη βασική τεχνογνωσία του προϊόντος εύκολα διαθέσιμη σε εσάς και τους πελάτες σας, ξεκινήσαμε το κανάλι GEBE Academy στο Youtube.

Μαζί με έναν μακρύ οδικό χάρτη προγραμματισμένων συνεδριών, είμαστε πάντα στην ευχάριστη θέση να δώσουμε προτεραιότητα και να σας υποστηρίξουμε με οπτικό υλικό για τις παρουσιάσεις σας στην αγορά.

Ενημερώστε μας για τα προϊόντα που θέλετε να δείτε, να συζητήσετε και να μοιραστείτε με την ομάδα και τους πελάτες σας.

The installation of a high-pressure pump

“A high-pressure pump must be installed in a workshop, because if it is installed incorrectly, it can easily lead to chipping in the fuel flow and consequently, in the worst case, engine damage.” This is the opinion of Benni Maier, owner of Autotechnik Maier, a car repair workshop and a GEBE test center. We let him guide us through the installation of a GEBE high-pressure pump and are pleased to be able to share this with you.

As a rule, no special tools are required for the professional installation of a GEBE high-pressure pump. The removal and installation varies from vehicle to vehicle. Let’s now move on to the removal of the old high pressure pump, and the installation of the new one.

After the high-pressure fuel pump has been removed according to the manufacturer’s instructions, the battery negative terminal is disconnected to prevent the electric fuel pump from starting.

Now, according to the manufacturer’s instructions, remove all attachments to get access to the high pressure pump. Remove the electrical connector here.

Next, remove the high-pressure fuel line and low-pressure fuel line. Open connections are to be closed here.  Loosen each screw alternately by half a turn to prevent the high-pressure pump from jamming.

Now you can remove the high-pressure pump

The tappet is now removed from the cylinder head. The gasket holes are cleaned and inspected for damage.

When attaching the pump, make sure that it does not tilt. First tighten the screws by hand, then tighten them alternately by half a turn each. (The correct torque can be found in the vehicle manufacturer’s documentation).

Now mount the high-pressure fuel line and the low-pressure line, as well as all add-on parts. Reconnect the battery negative terminal.

Switch on the ignition and check for fuel leakage in the engine compartment. Now start the engine and check again. A subsequent test drive is recommended.

Due to the improved valve design, the GEBE high pressure pump achieves at least the mileage of the OE equipment.

If you want to know more about our high pressure pumps or our GEBE Test Center, feel free to contact us.

Stay safe! Your team from IKA-Germany .